REXSTEEL
Corrugated structural plate e-coating process from NET site-assessment material
Home / Functional e-coated structural plate
NEW / MATERIAL INNOVATION

Functional E-Coated Corrugated Structural Plate

E-coating technology tested for adhesion, abrasion resistance and weathering performance.

NET site-assessment material · Structural plate e-coating process
FUNCTIONAL E-COATING

Functional E-Coated Corrugated Structural Plate

Electrolytic etching prepares the bonding surface. Zirconium pretreatment and e-coating then improve surface protection of galvanized corrugated structural plate.

01 / TECHNOLOGY

NET New Excellent Technology

Certification documents for environmentally friendly surface treatment and e-coating technology.

02 / INNOVATION

Innovative Product designation

View the Innovative Product designation certificate for functional e-coated corrugated structural plate.

03 / PROCUREMENT

Procurement price negotiations underway

Price negotiations are ongoing. Registration with Korea’s Public Procurement Service has not yet been completed.

TESTED SURFACE PERFORMANCE

Adhesion. Abrasion. Weathering.
See the difference in the test results

Results from the 2024 NET and 2026 Innovative Product presentations. Read them with the test conditions and comparator specimens.

01 / ADHESION0classification

Adhesion retained after exposure

Cross-cut adhesion classification 0 at 1 mm spacing after separate 72-hour acid, alkali, water and humidity exposures.

2026 presentation, p.23 · KCL
02 / ABRASIONApprox. 40% reduction

Lower abrasion mass loss than the comparator

Mean abrasion mass loss: 97 mg → 58 mg. CS-17 wheel, 1,000 g load, 1,000 cycles.

2026 presentation, p.24 · KCL · Koptri
03 / SALT SPRAY500hours

No abnormalities in neutral salt spray testing

Neutral salt spray results for 14 original and maximum-size variants reported in the presentation.

2026 presentation, p.26 · KTR
04 / WEATHERING1,000hours

No visible defects after accelerated weathering

No cracking, blistering, splitting, flaking or peeling in accelerated UV weathering testing.

2024 NET site-assessment presentation, p.15 · KCL
Test conditions and reported results
PropertyTest conditionsReported result
Adhesion after acid / alkali exposure10% sulfuric acid or 10% sodium hydroxide, 23±1°C, 72 h each · 1 mm cross-cut spacingClassification 0
Adhesion after water / humidity exposureWater: distilled water, 60±1°C, 72 h / Humidity: 60±1°C, 95±5% RH, 72 hClassification 0
Abrasion resistance comparisonCS-17 · 1,000 g load · 1,000 cyclesComparator: 97 mg → candidate product mean: 58 mg
Permeation resistance comparison10% sodium chloride · 10% sodium hydroxide · 30% sulfuric acid, 48 h eachNo abnormalities in the candidate product / red rust on the comparator in the presentation
Neutral salt spray500 h · 2026 presentationNo abnormalities reported
Accelerated weatheringUV, 1,000 h: KS M ISO 4892-3 · KS A 0063, 2024 NET material
Xenon, 300 h: 2026 presentation
No abnormalities in either test
Additional testsImpact resistance · Pinholes · Leaching of four heavy metals, 2026 presentationNo abnormalities reported in the presentation

Sources: 2024 NET site-assessment presentation, p.15; Innovative Product presentation dated 14 April 2026, pp.23–26. Results apply to the tested specimens and conditions, not service-life predictions. The abrasion reduction is approximately 40.2%, calculated from mean losses of 97 mg and 58 mg. NET certification and Innovative Product designation are separate from procurement registration. Price negotiations are ongoing; registration is not yet complete.

PROCESS

Surface technology behind the product

Explore the process, product range and test information through the coating equipment and product literature.

Coating bath and structural plate, NET site-assessment material, p.8
2024 NET site-assessment material, p.8 · E-coating process

Electrolytic etching in sodium bicarbonate solution creates microscopic surface texture, followed by zirconium pretreatment and waterborne acrylic e-coating. The process is designed to improve adhesion and resistance to corrosive and abrasive environments.

Final catalogue in preparation
PROCESS GALLERY

Inside the e-coating line

Actual process and finished-product photographs from pp.8–9 of the 2024 NET site-assessment presentation.

NET presentation · Plate above coating bath
Structural plate above the coating bath
NET presentation · E-coating demonstration
E-coating demonstration
NET presentation · Drying process
Drying process
Grey e-coated structural plate · Surface geometry retouched
Grey e-coated structural plate · Surface geometry retouched
CERTIFICATES & CATALOG

Related documents in one place

Select a document to view the original.

TECHNOLOGY / NET

From pretreatment to coating,
one connected process.

Technology overview based on REXSTEEL’s 2024 NET first-stage and site-assessment presentations.

01 / BACKGROUND

Coating large galvanized components

The presentation identifies surface preparation and improved paint adhesion on large hot-dip galvanized components as development objectives.

02 / SURFACE

Electrolytic etching

Electrolytic etching in sodium bicarbonate solution creates a micro-textured surface for paint adhesion.

03 / COATING

Pretreatment and e-coating

Zirconium pretreatment followed by functional e-coating, developed for large corrugated structural plates.

1Electrolytic etching
2Rinse
3Zirconium pretreatment
4Rinse
5Functional e-coating
6UF rinse 1
7UF rinse 2
8Infrared drying
TEST SPECIMENS

Surface performance, shown in test specimens

Actual specimen photographs from the test documentation, showing adhesion assessment and before-and-after abrasion testing.

E-coated adhesion specimens after acid, alkali, water and humidity exposure
Adhesion specimens after exposure · 2026 presentation, p.23
Functional e-coated specimens before and after abrasion testing
Candidate product before / after abrasion testing · 2026 presentation, p.24
PROCUREMENT STATUS

Procurement price negotiations underway

Functional e-coated corrugated structural plate is under procurement price negotiation. Registration with Korea’s Public Procurement Service is not yet complete.

Confirmed models, specifications, item identifiers and purchasing guidance will be provided after registration.

Find the right solution
for your project, together.

Contact us about products, design and construction support.

Contact us ↗